DMC sd 60 KRCS - AUTOMATIC WIDE BELT SANDER.
MAIN FEATURES
-LONG BELTS: 85 INCHES LENGTH FOR GREATER FINISHING AND PRODUCTIVITY.
-PHOTOCELLS WITH “PRESENCE DETECTION SYSTEM” TO ENSURE ALWAYS THE CORRECT CENTERING OF THE ABRASIVE BELT.
-FLOATING PRESSURE ROLLERS: PRECISE AND CORRECT WORKPIECES HOLDING IN ALL WORKING CONDITIONS
TECHNICAL DATA:
working width: 1,100mm
min/max. working thickness:4-170 mm.
sanding belt width: 1,115 mm.
sanding belt length: 2,150 mm.
1st unit motor power: 24 HP
2nd unit motor power: 24 HP.
3rd unit motor power: 18 HP.
feed belt motor power: 4HP.
feed speed: 3.5/18 m/min.
GENERAL FEATURES:
Base and working table
Steel structure with electric cabinet on the machine front
Sanding belts introduction from the machine left side
Powered adjustment of working thickness
Main motor positioned inside the base
Electrical equipment
Electromechanical keyboard positioned on the machine front side
Automatic star-delta start of the main motor
Overload protections on the motors
Motors in isolation class IP54
Emergency and safety devices
Automatic brake for rapid shutdown of the operating group
Hand-safety emergency device in the infeed panel area
Front and rear emergency pushbutton
Padlockable main switch
Automatic emergency stop machine for:
- sanding belt breaking
- not-tensioned sanding belt
- lateral outplacement of sanding belt
- absence of compressed air
- overload on main motor
BASIC MACHINES STANDARD EQUIPMENT
Electronic ammeter on main motor for readout of absorbed power
Electronic readout of working thickness
Electronic oscillating of sanding belts
Rubber-coated pressure rollers
Infeed anti-kickback vertically pivoted roller on 1st operating group
60 Shore rubber feed belt
Infeed/outfeed workpieces support rollers with two rollers
Automatic device for feed belt tracking and tensioning
DMC sd 60 KRCS 110 - Automatic wide belt planer/sander
with 1st “K” group (spiral planer), 2nd “R” group (175mm 65Sh roller) and 3rd “CS” combined group (160mm 45Sh roller/pad)
480 voltage
Frequency 60 hz
"B" version for KRCS complete with:
on/off pneumatic selector for planer, 1st “K” group
on/off pneumatic selector for roller, 2nd “R” group
on/off pneumatic selector for roller, 3rd “CS” group
“MESAR” elastic sectional pad
on/off pneumatic selector for pad
“Logic 50 K” electronic control
electronic positioning for working table
Infeed support rollers for long workpieces
equipped with no. 5 idle rollers
MAIN FEATURES
-LONG BELTS: 85 INCHES LENGTH FOR GREATER FINISHING AND PRODUCTIVITY.
-PHOTOCELLS WITH “PRESENCE DETECTION SYSTEM” TO ENSURE ALWAYS THE CORRECT CENTERING OF THE ABRASIVE BELT.
-FLOATING PRESSURE ROLLERS: PRECISE AND CORRECT WORKPIECES HOLDING IN ALL WORKING CONDITIONS
TECHNICAL DATA:
working width: 1,100mm
min/max. working thickness:4-170 mm.
sanding belt width: 1,115 mm.
sanding belt length: 2,150 mm.
1st unit motor power: 24 HP
2nd unit motor power: 24 HP.
3rd unit motor power: 18 HP.
feed belt motor power: 4HP.
feed speed: 3.5/18 m/min.
GENERAL FEATURES:
Base and working table
Steel structure with electric cabinet on the machine front
Sanding belts introduction from the machine left side
Powered adjustment of working thickness
Main motor positioned inside the base
Electrical equipment
Electromechanical keyboard positioned on the machine front side
Automatic star-delta start of the main motor
Overload protections on the motors
Motors in isolation class IP54
Emergency and safety devices
Automatic brake for rapid shutdown of the operating group
Hand-safety emergency device in the infeed panel area
Front and rear emergency pushbutton
Padlockable main switch
Automatic emergency stop machine for:
- sanding belt breaking
- not-tensioned sanding belt
- lateral outplacement of sanding belt
- absence of compressed air
- overload on main motor
BASIC MACHINES STANDARD EQUIPMENT
Electronic ammeter on main motor for readout of absorbed power
Electronic readout of working thickness
Electronic oscillating of sanding belts
Rubber-coated pressure rollers
Infeed anti-kickback vertically pivoted roller on 1st operating group
60 Shore rubber feed belt
Infeed/outfeed workpieces support rollers with two rollers
Automatic device for feed belt tracking and tensioning
DMC sd 60 KRCS 110 - Automatic wide belt planer/sander
with 1st “K” group (spiral planer), 2nd “R” group (175mm 65Sh roller) and 3rd “CS” combined group (160mm 45Sh roller/pad)
480 voltage
Frequency 60 hz
"B" version for KRCS complete with:
on/off pneumatic selector for planer, 1st “K” group
on/off pneumatic selector for roller, 2nd “R” group
on/off pneumatic selector for roller, 3rd “CS” group
“MESAR” elastic sectional pad
on/off pneumatic selector for pad
“Logic 50 K” electronic control
electronic positioning for working table
Infeed support rollers for long workpieces
equipped with no. 5 idle rollers