SCM DMC SD 10 CS 95 37" Single Head Wide Belt Sander.
(R000801).
Machine Standard Features:
Rubber coated pressing rollers before and after sanding unit.
Additional flexible hold-down plate before sanding unit.
.7 HP 2 speed feed unit. Feed speeds set at 15 and 30 feet per minute.
Electronic digital thickness readout of work table position.
Electronic positioning of the work table.
Powered table lifting by means of four heavy duty motor and lifting columns double fastened at both top and bottom of the lifting columns to provide exceptional table stability.
Accurate and reliable electronic tracking of abrasive belt.
Pneumatic belt tensioning with center fulcrum to compensate for tapering of abrasive belt.
Front and rear emergency stop buttons.
Automatic emergency stop of machine for:
- sanding belt breaking, tensioning, over tracking.
- opening of the access door to the operating groups.
- absence of compressed air.
- overload on main motors.
Amperage meter for main motors allows maximum utilization of available horsepower.
Main disconnect switch with the ability to be locked out by padlock.
50 shore, negative profile (waffle style) rubber feed mat.
Infeed and Outfeed tables with 2 rollers each.
Automatic table thickness device.
Working Unit Specifications:
1st Working Unit
Working Unit Type: Combination Head:
Motor Hp: 18 HP
Motor Type: Single Speed
Abrasive Belt Speed: 18 mps
Drum Size: 120 mm (4.75”)
Drum Type: 85 Sh Rubber
Platen Size: 50 mm (2”)
Platens Included: Two
Abrasive Belt Length: 60”
Technical Specifications:
Working Width 950 mm (37”)
Number of Heads Available 1
Feed Motor .7 HP
Feed Speed 15 or 30 fpm
Maximum Work piece Thickness 160 mm (6.25”)
Minimum Work piece Length 12.5 inches
Abrasive Belt Size 37” X 60”
Compressed Air Requirements 6 Bar (88 PSI.)
Dust Outlets 1 outlets @ 140 mm (5.5”)
Exhaust Requirements 900 CFM
Power Requirements 54 amps @ 230 Volts/3 phase
(R000801).
Machine Standard Features:
Rubber coated pressing rollers before and after sanding unit.
Additional flexible hold-down plate before sanding unit.
.7 HP 2 speed feed unit. Feed speeds set at 15 and 30 feet per minute.
Electronic digital thickness readout of work table position.
Electronic positioning of the work table.
Powered table lifting by means of four heavy duty motor and lifting columns double fastened at both top and bottom of the lifting columns to provide exceptional table stability.
Accurate and reliable electronic tracking of abrasive belt.
Pneumatic belt tensioning with center fulcrum to compensate for tapering of abrasive belt.
Front and rear emergency stop buttons.
Automatic emergency stop of machine for:
- sanding belt breaking, tensioning, over tracking.
- opening of the access door to the operating groups.
- absence of compressed air.
- overload on main motors.
Amperage meter for main motors allows maximum utilization of available horsepower.
Main disconnect switch with the ability to be locked out by padlock.
50 shore, negative profile (waffle style) rubber feed mat.
Infeed and Outfeed tables with 2 rollers each.
Automatic table thickness device.
Working Unit Specifications:
1st Working Unit
Working Unit Type: Combination Head:
Motor Hp: 18 HP
Motor Type: Single Speed
Abrasive Belt Speed: 18 mps
Drum Size: 120 mm (4.75”)
Drum Type: 85 Sh Rubber
Platen Size: 50 mm (2”)
Platens Included: Two
Abrasive Belt Length: 60”
Technical Specifications:
Working Width 950 mm (37”)
Number of Heads Available 1
Feed Motor .7 HP
Feed Speed 15 or 30 fpm
Maximum Work piece Thickness 160 mm (6.25”)
Minimum Work piece Length 12.5 inches
Abrasive Belt Size 37” X 60”
Compressed Air Requirements 6 Bar (88 PSI.)
Dust Outlets 1 outlets @ 140 mm (5.5”)
Exhaust Requirements 900 CFM
Power Requirements 54 amps @ 230 Volts/3 phase